Oil Change R75 MGZT Diesel by Arctic


User avatar
Arctic
(Trader)
This is a pictorial how to on how I do an oil change on the R75 MGZT diesel.

Hopefully this will help new members and owners if they decide to do there own oil change at some time.

My first bit of advise is get all your tools and items you will need together and allocate your self a day for the oil change to take place.

On the day of the oil change drive the car for at least 5 miles this will get the oil hot and help with draining the old oil out, once you return from the drive either jack the car up onto axle stands or drive onto ramps if you have some.

You can now remove the under tray ready for when you drain the oil Fig 1/2/3/4 (a)
Image1a

Image2a

Image3a

Image4a

Now the under tray has been removed turn your attention to removing the engine cover, some may leave it in place but as I was changing all the filters I removed the engine cover, in my opinion it helps as you have a little bit more room, tools need are 8mm socket. Fig 1/2/3

Image1

Image2

Image3

With all three engine cover bolts removed you can lift the engine cover off putting it safe to one side with the bolts. Fig 4/5/6
Image4

Image5

Image6

The next job is to loosen not remover yet the oil filter top you will need a 36mm shallow socket Fig 7/8
Image7

Image8

Below the oil filter is the alternator this must be covered up so no oil drips onto it as damaged can occur thus causing you to change it should damage occur. Fig 9
Image9

Use some good rags, cloths to cover the alternator up as here below Fig 10
Image10

With the rags in place you can now loosen the oil filter top a little Fig 11/12
Image11

Image12

Now it is time to get under the car and drain the oil which should have settled nicely in the sump, the sump is situated at a great angle so the oil will drain freely you will need a 15mm socket and 15mm ratchet spanner to remove the sump bolt. Fig 13/14
Image13

Image14

Once you have cracked the bolt you can use the 15mm ratchet spanner it gives you more control over the bolt again in my opinion. Fig 15
Image15

Place your oil catcher or bucket which ever you are using under the sump area ready to catch the oil once you remove the sump bolt. Fig 16
Image16

With the sump bolts loosened you can slowly remove it always keeping pressure on it so oil does not yet pour from the sump. Fig 17/18
Image17

Image18

As you can see from this photo I am still keeping pressure on the bolt to stop the oil from pouring out, i am now ready to remove the bolt quickly so the oil will drain straight into the oil container below.Fig 19
Image19

With the bolt removed fast the oil pours out into the container and I have my hands out of the way. Fig 20/21
Image20

Image21

Leave the oil draining for a while, you can now think about removing the oil filter Fig 22
Image22

After you have had a coffee or cup of tea giving time for the oil to drain from the oil filter pot, you are ready to carry on with the oil change, removing the oil filter top, (quick little tip tighten up the oil filter top more than you would normally) then re-loosen this will become apparent later.

Undo and release the top slowly making sure you have a small container ready to drop the top into, an old windscreen washer container cut in half is good Fig 23/24
Image23

Image24

Once loosened enough you can remove with your hand Fig 25
Image25

Drop it into the container, as you can see when I re-tightened the oil filter top earlier it as crushed the oil filter helping it stay in place when I remove the top, you don't have to do this as you can remove it with your fingers after the top as been removed if you so wish. Fig 26
Image26

Now the filter as been removed you can see I split a little of the oil but the rag as done it's job,there is still some oil in the pot I like to remove this also Fig 27
Image27

I need to get this oil out of the pot as I want it to be clean inside as best it can before adding the new filter Fig 28
Image28

To do this use some more old rags to soak up the oil left over in the pot Fig 29
Image29

pot cleaned out good enough I think Fig 30
Image30

With your new filter you will have some new O-rings some come with three O-rings some with just the large one as in this case below, disregard the copper washer it is not used on the diesel but they all have then in the box ? Fig 31
Image31

The large O-ring needs to be changed also the small ones if you have them in you filter box Fig 32
Image32

First remove the old filter Fig 33
Image33

Now you can remove the old O-ring use an hook tool if you have one if not a small thin screwdriver will do Fig 34
Image34

Dispose of the O-ring safely as you will be fitting the new one shown with the new filter here Fig 35
Image35

Add the new O-ring to the filter top Fig 36
Image36

The new filter can now be fitted into the oil chamber Fig 37/38
Image37

Image38

Followed by the filter top making sure you keep it centre lower it down and do it up hand tight Fig 39/40
Image39

Image40

Finally tighten it up with the socket (Nm25 = 18lbf ft) do not over tighten as you will crush the filter inside damaging it Fig 41
Image41

Remove the rags and make sure all is clean and dry Fig 42
Image42

Time to make another coffee while that cools you can pop back under the car wipe any dripping oil, then re-fit the sump bolt using a new one if you have one if not the old one should be ok. Fig 43
Image43

Finger tight sump bolt Fig 44
Image44

Tighten the sump bolt up with the ratchet spanner 15mm Fig 45
Image45

Re-fit the under tray drop the car off the axle stands or ramps if you used ramps push it off slow, get someone to help if you can, if not you could add the 5ltrs of oil first then drive it off you will then need to wait for the oil to drain back down before adding anymore.

You can now add you new oil use a funnel it is even better if you can get someone to hold the funnel for you, this will avoid spillage Fig 46
Image46

Add a full 5ltrs at first Fig 47
Image47

While the oil makes it's way down to the sump re-fit the engine cover Fig 48
Image48

Add one more ltr then start the car so the oil fills the oil filter pot, let the oil drain down again add another 400ml take car for a quick drive couple of miles return let the engine tick over for about 5 minutes then turn the engine off, let oil settle again for about 15 minutes recheck level top up to max if you need to good luck Arctic
Pearl Firefrost
ARCTIC

Posted 11 Mar 2015, 23:41 #1 


Top